Page 16 - FAST FEED MILL Brochure_metric 2022

OAL

A LF
FFT3 EFM-MM 03 DCX DC THSZMS DCONMS Rd°
Endmills with a MULTI-MASTER
Threaded Adaptation Carrying APMX
Single-Sided Small Trigon 17° DRVS
Inserts for Fast Feed Milling

Designation DCX (1) DC APMX AE (2) CICT (3) LF DCONMS THSZMS OAL DRVS (4) RMPX° (5) MDN (6) MDX (7) MIID (8) kg
FFT3 EFMD10/.39-2MMT06-03 10.00 5.60 0.60 2.2 2 10.00 9.70 T06 16.30 8.0 6.9 15.60 19.00 FFT3 WXMT 030206T 0.02
FFT3 EFMD12/.47-3MMT08-03 12.00 7.60 0.60 2.2 3 15.00 11.70 T08 22.50 10.0 4.7 19.60 23.00 FFT3 WXMT 030206T 0.03
FFT3 EFMD16/.63-4MMT10-03 16.00 11.60 0.60 2.2 4 20.00 15.30 T10 31.30 13.0 2.9 27.60 31.00 FFT3 WXMT 030206T 0.05
FFT3 EFMD20/.78-5MMT12-03 20.00 15.60 0.60 2.2 5 25.00 19.00 T12 38.30 16.0 2.0 35.60 39.00 FFT3 WXMT 030206T 0.07
FFT3 EFMD25/.98-6MMT15-03 25.00 20.60 0.60 2.2 6 30.00 24.00 T15 47.00 20.0 1.5 45.60 49.00 FFT3 WXMT 030206T 0.00
• Radius for programming 1.1 mm • To generate a straight surface without cusps, the width of cut must not exceed DC
(1) Cutting diameter maximum
(2) Maximum plunging width
(3) Number of inserts
(4) Torque key size
(5) Maximum ramping angle
(6) Machinable diameter minimum for interpolation
(7) Machinable diameter maximum for interpolation
(8) Master insert identification

Spare Parts

Designation
FFT3 EFM-MM 03 TS 18041I/HG TS 18041I/HG (a) T-6IP/51
(a) Recommended tightening torque: 0.5 (Nm)

FFT3 EFM-03 A LH OAL
Endmills Carrying Single- Rd°
Sided Small Trigon Inserts DCX DC DCONMS
for Fast Feed Milling APMX
17° A

Designation DCX (1) DC APMX AE (2) CICT (3) LH OAL DCONMS Shank (4) RMPX° (5) MDN (6) MDX (7) MIID (8) kg
FFT3 EFM D08-1-080-C12-03 8.00 3.60 0.60 2.2 1 20.0 80.00 12.00 C 1.1 11.60 15.00 FFT3 WXMT 030206T 0.00
FFT3 EFM D10-2-080-C10-03 10.00 5.60 0.60 2.2 2 20.0 80.00 10.00 C 6.9 15.60 19.00 FFT3 WXMT 030206T 0.11
FFT3 EFM D12-3-120-C12-03 12.00 7.60 0.60 2.2 3 25.0 120.00 12.00 C 4.7 19.60 23.00 FFT3 WXMT 030206T 0.14
FFT3 EFM D16-4-140-C16-03 16.00 11.60 0.60 2.2 4 35.0 140.00 16.00 C 2.9 27.60 31.00 FFT3 WXMT 030206T 0.18
FFT3 EFM D20-5-160-C20-03 20.00 15.60 0.60 2.2 5 43.0 160.00 20.00 C 2.0 35.60 39.00 FFT3 WXMT 030206T 0.37
FFT3 EFM D25-6-180-C25-03 25.00 20.60 0.60 2.2 6 53.0 180.00 25.00 C 1.5 45.60 49.00 FFT3 WXMT 030206T 0.62
• Radius for programming 1.1 mm • To generate a straight surface without cusps, the width of cut must not exceed DC
(1) Cutting diameter maximum
(2) Maximum plunging width
(3) Number of inserts
(4) C-Cylindrical
(5) Maximum ramping angle
(6) Machinable diameter minimum for interpolation
(7) Machinable diameter maximum for interpolation
(8) Master insert identification

Spare Parts

Designation
FFT3 EFM-03 TS 18041I/HG (a) T-6IP/51
(a) Recommended tightening torque: 0.5 (Nm)

16 FAST FEED MILLING